New Project 2017 Silverado
+2
ant7377
Iggy
6 posters
G3GM :: Media :: Non G3 Projects
Page 3 of 3
Page 3 of 3 • 1, 2, 3
Re: New Project 2017 Silverado
Dude, we just need to weld a nut to what's left of the bolt and we'll get it out proper. Worked like a charm on my son's truck.
g3chevy / Mr Pontiac- Donating Member
- Street Cred : 34
Re: New Project 2017 Silverado
Hey Joe. I’m glad that you are liking your truck. It’s pretty amazing what you can tune on these trucks. You can pick up such a better feel just tuning the transmission. Did you also tune your gas pedal? Mine is turned all the way up. It actually has throttle response now. I can turn my spin control switch off now and I can leave 2 black marks into second gear now. It even gets a little sideways! Good luck.
REVINKEVIN / Mr. 600+HP- G3GM Senior Member
- Street Cred : 19
Re: New Project 2017 Silverado
REVINKEVIN / Mr. 600+HP wrote:Hey Joe. I’m glad that you are liking your truck. It’s pretty amazing what you can tune on these trucks. You can pick up such a better feel just tuning the transmission. Did you also tune your gas pedal? Mine is turned all the way up. It actually has throttle response now. I can turn my spin control switch off now and I can leave 2 black marks into second gear now. It even gets a little sideways! Good luck.
Sounds like you have one fun daily driver now! Maybe that's why you work so much, you just like the drive there and back!
g3chevy / Mr Pontiac- Donating Member
- Street Cred : 34
Re: New Project 2017 Silverado
It does add some excitement. We actually had a 3 way drag race from a red light this morning at about 5:10. It gets out on those big 4-door 4x4 trucks that Houston is full of.
REVINKEVIN / Mr. 600+HP- G3GM Senior Member
- Street Cred : 19
Re: New Project 2017 Silverado
Hey. I bought a 6.2 long block and I have started working on it. I am going to add a Texas Speed 3 bolt cam kit, DOD delete kit, and ported heads. It's funny that I saw a video of an Indy Cylinder head 426 HEMI that probably cost around $20,000 and it dynoed less than a cammed LT1 Gen V engine with ported heads. That's crazy. The little truck that I drive to work will have more HP than an LS6 Chevelle and a HEMI Cuda. I will be working on the heads tomorrow. I have already taken the valves and springs out and I need to clean that insane Direct Injection goo out of the heads. I am also porting an L86 intake and adding a 95mm LT5 throttle body. I still need to get another driveshaft built so I can go 150 mph. Yes, I am trying for 150 mph in this truck. Of course I drive down to Mexico to do that. Wish me luck.
REVINKEVIN / Mr. 600+HP- G3GM Senior Member
- Street Cred : 19
Re: New Project 2017 Silverado
You've been busy! That truck is gonna be too nice and too fast for a work truck!
g3chevy / Mr Pontiac- Donating Member
- Street Cred : 34
REVINKEVIN / Mr. 600+HP- G3GM Senior Member
- Street Cred : 19
fasrnur likes this post
REVINKEVIN / Mr. 600+HP- G3GM Senior Member
- Street Cred : 19
Limey SE and fasrnur like this post
Page 3 of 3 • 1, 2, 3
G3GM :: Media :: Non G3 Projects
Page 3 of 3
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Yesterday at 1:56 pm by REVINKEVIN / Mr. 600+HP
» Pate Swap Meet - Texas Motor Speedway - G3 Parts Goldmine
Yesterday at 12:20 pm by g3chevy / Mr Pontiac
» '73 Laguna coupe - factory 454- SoCal $2500
Fri May 17, 2024 4:38 pm by Mcarlo77
» Dash Solutions
Fri May 17, 2024 3:22 pm by 76 Malibu
» Rusty's progress Done stuff again LOL
Thu May 16, 2024 12:56 pm by Limey SE
» 1973 4 door laguna frame same as 1973 2 door chevelle
Tue May 14, 2024 4:39 pm by chevelleman
» Anyone good at photoshop?
Mon May 13, 2024 12:50 pm by 76 Malibu
» '77 Monte Carlo Landau - Parting out - 61k miles on car
Fri May 10, 2024 5:02 pm by Matchstx
» Dash assembly for 73-77 Malibu/Monte/El Camino,etc.
Fri May 10, 2024 2:48 pm by Limey SE
» Window louvers
Fri May 10, 2024 12:47 pm by JCervantes10