G3GM
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

+16
76Chevelle2Tone
zucchi
bucket
g3chevy / Mr Pontiac
Limey SE
REVINKEVIN / Mr. 600+HP
ant7377
73ss
Joe73
bigredlaguna
thatfnthing
Mcarlo77
77camino
fasrnur
Zaptiah
S3SS
20 posters

Page 9 of 11 Previous  1, 2, 3 ... 8, 9, 10, 11  Next

Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by g3chevy / Mr Pontiac Thu Jun 15, 2023 11:23 pm

Limey, did a wire harness swap a while back on a 77 Malibu that I eventually sold. The engine harness donor was a 76 Laguna. Everything plugged in nicely and had only one issue. I could not get the horn to work. Come to find out the harness was pinned differently for the horn from 76 to 77. Popped that pin out and placed it where it would be for a 77 and then worked perfectly. Hope this helps.
g3chevy / Mr Pontiac
g3chevy / Mr Pontiac
Donating Member
Donating Member

Street Cred : 34

Limey SE and 76Chevelle2Tone like this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Fri Jun 16, 2023 12:19 am

Thank you my friend As far as I know the light harness for Monte Carlo and Malibu arent the same So as Long as the engine side gets me to where I need to be I can do the Light side at a later date

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by g3chevy / Mr Pontiac Fri Jun 16, 2023 8:35 am

Sorry Limey, thought you were changing out the whole harness. You should be good then.
g3chevy / Mr Pontiac
g3chevy / Mr Pontiac
Donating Member
Donating Member

Street Cred : 34

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Fri Jun 16, 2023 10:00 am

g3chevy / Mr Pontiac wrote:Sorry Limey, thought you were changing out the whole harness. You should be good then.


I will eventually as he would not split them in the sale so will just do motor side for now and then see how the other wiring is

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Thu Jun 29, 2023 1:29 pm

WELLLL  454 Valve covers FINALLY SOLD took a big hit on them but they paid for the 15x10 wheels and short derby Caps and had $6 bucks left over woo hoo

Cant go outside because of the wildfires from Canada thanks for that EHHH ! anyways 8 days now stuck in house except picking up daughter from work Tuesday other than that I have been isolated in house Anyways the dream of Having 15x10 15x8 with short derby caps (NON ORIGINAL's) is finally here (yes I am keeping the Turbines but getting them restored over winter)

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35755310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35732710
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35695910
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Vsw-5510

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

76Chevelle2Tone likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Fri Jun 30, 2023 1:04 pm

THEY HAVE ARRIVED damaged but arrived little nicks around the whole face of Wheel oh well 70 dollar e gift card later I will be mounting the tires soon I guess (they couldn't get the replacements to me before next weekend so just took the gift card)

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35763210
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35698210
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35765910

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Thu Jul 06, 2023 11:18 pm

Just like posting updates MAYBE JUST MAYBE tomorrow Can start the wiring aspect of the 454 supposed to be not as hot .... BUT AS FOR NOW I FINALLY Have my wheel set up I have been chasing for a very long time...... NO THE TIRES ON THE REAR ARE NOT staying till I get new when running no sense buy new ones and let sit while finishing up details, But any who
15x10 rear (255/60r15 that fell into my lap today) and front 15x8 235/60r15 (will be switching to 255/60r15 when I upgrade the rears) and the Vision wheel short derby caps Man now have to repaint the fronts they look like hell from trim rings WHICH I WILL NOT BE RUNNING anyways y'all thanks for reading

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35873810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35770510
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35870510

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35866310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35873510
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35874510
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35874511
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35875910
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35875710


Last edited by Limey SE on Tue Jul 11, 2023 11:11 pm; edited 1 time in total

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by g3chevy / Mr Pontiac Fri Jul 07, 2023 10:14 am

Looking good! Love those short derby caps!
g3chevy / Mr Pontiac
g3chevy / Mr Pontiac
Donating Member
Donating Member

Street Cred : 34

Limey SE likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Mon Jul 10, 2023 10:48 pm

Rut roh Man,  Wiring and plugs for most part done NEXT is engine harness Had to take break with no shade can only do so much, Wiring harness is next on agenda Gonna take a earlier start tomorrow since wifey doesn't work and put up my shade ten I should have done that today Oh well One more item out of the way
P,S. Jason Fuller Sr. thanks for the Matching air filter to my Valve covers Clapp Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 978692 <?>



Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35640410
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35638610
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35847810Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 555-4110
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36004810Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35637310

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35641610

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Finn Monte and 76Chevelle2Tone like this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Tue Jul 11, 2023 11:17 pm

More test fitting to see what works and ta da It came together LOL Header in drive side is next ohhhh fun

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36008110
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35644310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36013710Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36008110
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35644310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36013710Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 555-4111


Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 978692 Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 978692

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Wed Jul 12, 2023 5:26 pm

Well went out between the rain showers and tornado watch's Power steering Pump has the right brackets now THNAK YOU Cameron @ICTBILLET  was missing two bolts and a spacer they sent new Kit BUT SBC one LOL Called them they OVERNIGHTED the right brackets with a Label to send SBC set back to them at there cost RADIATOR HOSE'S ARE TEST FITTED ONLY FOR LENGTH that way can take to parts store and match it up


Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36056710
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36073210
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Power_10Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36107410
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36086910
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36067910

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by g3chevy / Mr Pontiac Fri Jul 14, 2023 11:28 am

Its coming along! What's your goal to get this fired up for the first time?
g3chevy / Mr Pontiac
g3chevy / Mr Pontiac
Donating Member
Donating Member

Street Cred : 34

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Fri Jul 14, 2023 12:02 pm

I need to have it done by Middle september at the latest to make the Invite for the Muscle Car and Corvette Nationals invite I had gotten for the 73-77 Spotlight this year Including the 1 of 1 Baldwin Motion 73 SS Chevelle they want them to be Side by Side Kind the Best of the First year 73 and a Special Last year 77

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

bucket and 76Chevelle2Tone like this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Sat Aug 05, 2023 1:01 pm

WELLL WELL Got off the injured reserve list again LOL had leg injury on my bad leg yet again, LOL Anywho Well got Ungrounded finally sort of LOL
Took all the accessories and water pump off to give the 454 a nice look after installation of it. Being sick and injured I am happy to be able to work on it yet again LOOKS 1000% better I think I HAVE THE RiGHT Length and fit for top hose Bottom still working on it.
1st and 2nd Picture was Before rest are after, Transmission install will hopefully be today or tomorrow

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 35936810Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36454610

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36538010
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36550610
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36453910
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36454810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36469810

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

76Chevelle2Tone likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Sat Aug 05, 2023 9:30 pm

Transmission all cleaned up and painted ready for install as Long as rain holds off with or without my helper its going in



Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36454010
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36454110
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36539510

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

76Chevelle2Tone likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Sat Aug 05, 2023 10:06 pm

I also had an OCD moment I had to clean up that rad Hose I cut it a tad more and I think this one is good enuf to use


Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36454510
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 36454011

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Wed Sep 06, 2023 7:57 pm

Well this morning turnt out great I finally have the correct length belts anyone else doing this 454 these are the belts you need for N0 A/C on car, now Rain is moving in and it looks like I will never get this stupid transmission in Arrrgggg

EDIT: FUEL PUMP IS IN,  NOW OUTTA PARTS AGAIN dodged the Rain and have the Pump back to the tank first time since 1984 when they yanked the blown up 305

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37341410
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37497710
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37528810Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37501810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37519810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37569310

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

76Chevelle2Tone likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Mon Sep 11, 2023 11:04 pm

More progress Yayyyyy  Then Rain Arrg


Heater hoses, fuel pump fitting (to allow fuel line run) Fuel filter, Negative Ground and Battery cable hooked up.... Gotta Find a pipe plug for Intake decide to stay in the stock location for heater hose's  Next project who knows Just keep plugging away

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37637310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37711110
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37770910Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37657310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37712510
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37761610

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

76Chevelle2Tone likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by bracketchev1221 Tue Sep 12, 2023 7:21 am

Limey SE wrote:Well this morning turnt out great I finally have the correct length belts anyone else doing this 454 these are the belts you need for N0 A/C on car, now Rain is moving in and it looks like I will never get this stupid transmission in Arrrgggg

EDIT: FUEL PUMP IS IN,  NOW OUTTA PARTS AGAIN dodged the Rain and have the Pump back to the tank first time since 1984 when they yanked the blown up 305

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37341410
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37497710
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37528810Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37501810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37519810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37569310

But did you remember the fuel pump pushrod!!!! Very Happy
bracketchev1221
bracketchev1221
G3GM Enthusiast
G3GM Enthusiast

Street Cred : 15

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Tue Sep 12, 2023 11:00 am

[quote="bracketchev1221"]
Limey SE wrote:

But did you remember the fuel pump pushrod!!!! Very Happy

YES SIR Double checked and rechecked again I have to check the gasket it looks like it fell out on the hole before I got the bolt in the block so will quadruple check on that LOL

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Wed Sep 13, 2023 1:25 am

Added the other 10" drive side Rally wheel tire and the two drive side Short Caps and dam .......

Well Looks like I am adding drop the 1" drop springs to front unless it settles more with transmission, exhaust and driveshaft in there I do not like the high front end and that is with the 454 Installed.

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37627710
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37674810
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37682610
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37778910
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37829310
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37829410Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37829311
Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 37850810

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by zucchi Wed Sep 13, 2023 8:34 am

Did you consider the weight of the A.I.R. system, weight of water in cooling system, and the AC compressor, condenser, hoses, etc.?
zucchi
zucchi
G3GM Member
G3GM Member

Street Cred : 4

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Wed Sep 13, 2023 12:57 pm

zucchi wrote:Did you consider the weight of the A.I.R. system, weight of water in cooling system, and the AC compressor, condenser, hoses, etc.?

No I am not running them, the car sat like this even with the 305 and the garb on it rear sat even lower till I added new springs and this is how it ended Up, It's almost like they put new springs in it before I got it, I am not sure about that though I know it's too high in front.

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by 76Chevelle2Tone Wed Sep 13, 2023 6:13 pm

That is about the meanest looking G3 Chevelle I've seen. What is the story about the grille? The first pictures showed a 77 grille but then showed what looks like a 75 grille. I didn't see an explanation but may have missed it.
76Chevelle2Tone
76Chevelle2Tone
G3GM Member
G3GM Member

Street Cred : 0

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Limey SE Wed Sep 13, 2023 8:56 pm

76Chevelle2Tone wrote:That is about the meanest looking G3 Chevelle I've seen. What is the story about the grille? The first pictures showed a 77 grille but then showed what looks like a 75 grille. I didn't see an explanation but may have missed it.

It came from a Member here and was the same as My Original Black SE had back when the previous Owner before me Had it and I loved the look and when I was offered this one I DIDN'T hesitate one second


Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 25-11010



Previous owner circa 1988 before storing till 2012 When I purchased it

___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE
Limey SE
Management
Management

Street Cred : 97

76Chevelle2Tone likes this post

Back to top Go down

Rusty's progress   Stinger scoop nearing completion (waiting on parts for motor) - Page 9 Empty Re: Rusty's progress Stinger scoop nearing completion (waiting on parts for motor)

Post by Sponsored content


Sponsored content


Back to top Go down

Page 9 of 11 Previous  1, 2, 3 ... 8, 9, 10, 11  Next

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum